# 1
Roadmaster Tail Light Wiring Kit with Bulbs
Always completely satisfied with Etrailer service and products! Jamie B is very knowledgable and courteous!
This was a good option for our 2020 Chevy Equinox because it does not tie into the tow vehicle electrical system and runs directly from the Motorhome electrical system.
# 2
Roadmaster Tail Light Wiring Kit for Towed Vehicles - LED Bulb and Socket - Red
This kit did the job very well. I could have bought each part separately and saved some money, but I went with the comfort knowing all these parts will work together to accomplish the job. I couldn't figure what LED bulb to use for both brake and turn signal. I routed the wire along the truck wiring harness for half the way to the front, then slipped it into the frame channel for the rest of the way. I used a Curt heavy, round 4 pin plug at the front grill. It was a bit of work and took many hours but came out clean!
I installed this on our 2019 Equinox towed. Love the convenience of just plugging in the towed vehicle. The most difficult part was deciding on what part of the light housing to drill the hole for the light socket.
# 3
RoadMaster Bulb and Socket Set for Tail Light Wiring Kits
Bought this light kit to install in the un-used bottom position in or 2005 Honda CR-V. No need to tap into vehicle's wiring harness. Easy to install, works great! Highly recommend.
This bulb kit is just what I needed to add trailer lights to my 'toad' vehicle. The sockets felt like quality items, it was simple to install. I had my own wire, I think it turned out great.
# 4
Blue Ox Tail Light Wiring Kit for Towed Vehicles - Integrated LED Bulb and Socket - Red
The tail light kit was easy to install, but I had to replace one of the lights within three months. The lights don't appear to be very durable. I purchased a different LED bulb as a replacement and it appears to be working good now.
Your products have been perfect, good fits and quality products. The towing base plate for my ford Fiesta fit with little modification and the ability to use standard tools. The instructions were right on. The tail light wiring kit also was easy and works great. Shipping was fast and delivery arrived as indicated. I will continue to do business with you.
# 5
Blue Ox Tail Light Wiring Kit - Bulb and Socket
I needed to wire our ‘17 Chevrolet Sonic for towing behind our Motorhome. My local shop wanted over $xxx to install such wiring. Online I found the Blue Ox wiring kit and decided to do it myself. The kit and instructions were very complete and informative and it took me about three hours to complete the installation. The time consuming part was removing and reinstalling trim and panels to hide the wiring inside the car. The thing I like most about this kit is it’s independent of the cars wiring system and I’m very happy with it.
I put this base plate on with the assistance of my wife very easy to install. Do recommend the video to install
# 6
Roadmaster Tail Light Wiring Kit w/ 7-Way to 6-Wire Connector - LED Bulb and Socket - Red
Installed in my 2024 Chevy Trax. I ran the wire harness up through the front fender, and along the DS rocker panel. No drilling into body required. However, I purchased extra loom to better protect exposed wires next to body. Additionally, I purchased extra wire to support the DS to PS taillight connections. Finally, be advised the plastic taillight assemply is "double hulled," so once you bore through the exterior of the assembly, you will need to drill again, into the lense. On this point, and to ensure a good fit of the bulb socket, a Dremel tool was used to grind down the plastic surface, to ensure a good flat and tight fit. Finally, I used the first cut-out to fashion a cap and to seal the light socket installation. See pic.
I am very happy with this kit. It gives you everything you need to setup an independent brake light system for you toad and therefore bypassing the vehicles internal wiring and computers. I went with this setup as I did not want to complicate my wiring or damage the internal systems of the toad. IT takes sometime to install, but once done hooking up and running the system is simple as plugging in your 7way connector. Combine this with a onboard braking system, and you have the perfect system to pull your two vehicle behind your RV.
What our customers are saying:
"Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair."