# 1
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
PERFECT FIT AND FAST...... i ordered a draw-tite class ll trailer hitch, t-one wiring harness and drawbar for my 2000 toyota camry..i had planned to have someone install it, but after seeing the instructions i did it myself in 30 minutes. great products.
Got a very good price on a trailer hitch for my '95 Camry. It was fairly simple to install (after watching etrailer.coms video). I use it to haul around my little utility trailer (Harbor Freight) and my 12 ft kayak (BassPro).
# 2
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
The hitch was exactly as ordered and fit perfectly. It is sturdy and a great value. It arrived quickly to CA. I really liked the videos and reviews on the site which gave me ideas and a sense of knowing I was installing everything correctly. I, like most of us, do not have access to a lift, but I used the ramps I have for oil changes on our cars. I just backed up on them and and chocked the front wheels. I also do not have lifting help and I am 71 so I set the hitch on a floor jack and my wife raised it up as I guided it in behind the bumper cover. I read a review that said he was able to install without dropping the muffler, and I did the same. Thanks for that tip, it was easy. Our Camry had weld nuts on both sides, maybe because it is one of the early 2011 models, which made it very easy. Let me say that I can see the muffler drop if you are using power tools. But if you are using good old had tools it really is not necessary. Another comment about the reviews. One review expressed concern over ware on the spare from the added bolts and the fact of permanently removing a factory bracket. This must have been a brother of mine as I had the same thoughts when I viewed the installation video before ordering. If you have a "donut" spare, like most, with it in the well look through the center hub with a flash light, the added bolts and plates are inside the rim area and never contact the actual tire. The second concern of the bracket removal, after looking at what it was bolted to, and where the added hitch, which is much stronger, is secured, I have no concerns the the bracket is now needed. After clearing the trunk, getting the tools together, and backing on the ramps. From start to final torque down of the bolts it was right at an hour. Note: My wife was very pleased with the hidden appearance of this hitch on "her" car. Always a success when the wife is happy. I recommend this model hitch and ETrailer and will refer friends.
Excellent product. Came with good instructions for install, does require a jack, wheel chocks, possibly jack stands, wrenches and ratchet and sockets, and a drill for bracketing thru trunk basin. Does take some time and patience especially dropping the muffler to get up and under it. The hitch itself is great. I use it for my bicycle rack. Once installed it is hidden other than the receiver. Very satisfied and glad I was able to install myself with the good instructions.
# 3
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
While the hitch appears to be built very solidly, I am disappointed in the quality of the powder coated finish. The product was received with multiple chips in the powder coating. Also, the weight label was applied crooked resulting in a very sloppy appearance. Now, instead of installing my hitch today, I have to research the best way to protect the exposed metal. It's unreasonable to have to repair a product straight out of the box.
etrailer delivered everything quickly and the instructions were very good. Installed this on my 2012 Camry to carry a bike rack only, so this hitch was perfect since it doesn't include a ball mount or ball. Figuring out how to drill the one inch holes in each frame rail was the hardest part - there are not a lot of metal bits that big available - my solution was to use a Harbor Freight #96275 step drill. All in all a great experience with etrailer.
# 4
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
My Iowa 2009 Camry has been in a garage it's whole life, so, that helped a lot. Used [online] etrailer video for ease of work. I took longer than they did as I had to work a bit to de-rust a couple of female bolt threads enough to get a bolt on easily.
We bought this 1.25" reciver hitch last year to accommodate a Kuat bike rack. The install was easy, the mounting holes lined up perfectly on our Camry, and the black painted hitch finish still looks new. We are very happy with this purchase.
# 5
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
I didn't cut off any underbody panel pieces. I just made a slit for the hitch to slide through. Also didn't cut off any heat shield. I drilled a hole for the 1/2" screw and torqued it to xx ftlb as instructed. Every thing worked fine. Hard to believe the video instructed to cut off that much. A bit crazy IMO. Also.. super snug fit. So snug I had trouble getting the M12 bolts to line up with the thread in the subframe. Pain the ass, but eventually got it in.
Fast delivery and everything fit perfect. Easy installation after watching etrailers videos. Lowest price I found on the internet for this hitch. Thanks for the great service.
# 6
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
Last Friday evening (right in the middle of October) I finally installed this Curt Trailer Hitch Receiver into my 2003 Toyota Camry. This is a Class II hitch but seems like a Class III one, very sturdy, and the installation was a success. I spend a lot of time cleaning the two holes on the driver side which were exposed to the elements for the last 18 years, and then I actually drove in three old bolts which I took off from the passenger side's muffler mount, and that was preparing for the actual installation of the hitch. I just worked by myself, as my young son is not too mechanically inclined and not interested in such a thing, so I used my own technique, just tied a pleated electrical cable (3/16" diam) to the rear bumper and then I lifted up and suspended the hitch to around the middle part of the bumper. Then I screwed in one bold on passenger end first, then tightening then cable, the screwed in a bolt into the middle hole on the driver side. I used two more bolts on the passenger side, and one more on the driver side. But I have an extra hole on the driver side so I reused one old bolt for the previously never-exposed hole and then tightening all bolts properly. Then on the next day I test drive my car with this hitch and Allen bicycle carrier rack which I loaded two bikes. On thing I noticed is that the lower hanging part of the hitch around the muffler tend to hit the asphalt when came out from a parking lot due to a dip in height (difference) from sidewalk to the main road, may be I was moving a little bit fast for the shock absorber to respond sufficiently. (BTW, our bikes' tires are low in air pressure or just flat because these were not used for a very long while, since COVID-19 pandemic began, and we avoided activities at any public parks and other places, and because we live in a condominium-type of apartments, we were not as "busy bees" except to stay put in the "hive".)
20 minutes install time. 1997 Toyota Camry LE V6. The car frame holes in back(4) were already threaded to accept supplied bolts. No need for nuts or U bolts. I recommend cleaning bolt holes to clear years of dirt/grime. The bolt fitment into threaded holes will be tight but bolts are correct. Makita rechargeable impact driver made install a snap. Use anti seize if you plan on removing at a later date.
# 7
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
Finally got the chance to install this hitch. The written instructions are marginal. They did not cover my hybrid version. The installation videos on etrailer were more helpful. The hitch was a bit off and contacts the tire well on one side. Installation by loosening the exhaust did not work for me. Mine was too tight and I could not move it out of the way to drill. I had to remove the muffler. The instructions for trimming are a bit aggressive. I was able to get the under cover installed with about 25% of the suggested cutting. One thing the instructions left out is a rear edge trim (however, the video did mention this). I also added a strip from (the heat shield scrap) to tie the cover back together and prevent flutter noise while driving. Installed, this hitch appears sturdy. I am sure it will last. Too bad it did not come with a pin or cover.
This is a quality product. It’s designed to fit the car perfectly. Please not though that you’ll need special tools to disconnect/drop the muffler system to install the hitch. I did not have tools to disconnect the muffler/exhaust hangers, so I wound up taking it to a mechanic that installed it for about $100.
# 8
Curt Trailer Hitch Receiver with Standard Drawbar - Custom Fit - Class II - 1-1/4"
Unbelievable fast delivery and securely packaged. Great price also. I was worried about purchasing something over the internet but the trailer hitch and wiring kit arrived securely packaged so there were no scratched, dents, or issues of any kind. I can't say enough positive things about my purchases. I definitely will be back to etrailer.com for more purchases.
Trailer hitch and wiring arrived as scheduled. Product fits the Toyota Camry perfectly. Installation was easy. Excellent service.
# 9
Curt Trailer Hitch Receiver with Standard Drawbar - Custom Fit - Class II - 1-1/4"
outstanding easy and just what I needed great product and price plus the wiring I ordered went in easy as pie
A difficult installation. But, that was not because of the hitch. Once the car was apart, the hitch fit perfectly and bolted right up.
# 10
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
This also worked
Very easy install and works perfectly
# 11
Curt Trailer Hitch Receiver with Standard Drawbar - Custom Fit - Class II - 1-1/4"
These are some of the best trailer hitches I know for the Toyota camry. Easy to install. I did order the wrong ball, had to buy another, to large of a bolt size.
Quality product. Worth every penny!
# 12
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
Very happy with purchase of this trailer hitch. Installed onto my 2008 Toyota 4Runner 2wd SR5 4.0 with no difficulties at all by myself. I recommend a second person to help lift the other side and to speed up the installation time but it’s possible with one man. 8 bolts, half inch drive, 19mm and 13mm sockets are all that is needed. Estimated novice time is 50 minutes and that is exactly what it took me. No cutting of fascia necessary. However, I did have to unhook the rubber latch on the tail pipe to get the passenger side bolts in (super easy and no problem to do). Two day shipping as promised straight to the front door. Highly recommend etrailer and this hitch receiver.
Arrived in a very timely manner in good shape. Easy install with instructions. I chose not to drop the exhaust as you can get the bolts in easy enough with it on. For the factory seven way plug and bracket i just bent it back and it works great. I have ordered through etrailer before and will do it again in the future ! thanks guys Tyler
# 13
Curt Trailer Hitch Receiver w/ Euro Drawbar - 1-7/8" Ball - Custom Fit - Class II - 1-1/4"
# 14
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
I installed this trailer hitch on my 2018 Toyota Sienna. It is very well-built, and fit perfectly. Customer service was very responsive when I had some questions, and responded right away, both by phone and email. The instructions were very good, but could benefit from additional information regarding cutting the car’s rear trim panel. In addition to the cut that needs to be made for the trailer hitch bolting plate to go through on the driver’s side , it also needs to be cut around the main bar / receiver area. Instead of cutting a big slot for the main bar, I cut out around the receiver plates, and put drain holes in the ends that would otherwise collect water. One shortcut that I found was that I was able to move the exhaust out of the way far enough by just removing the rearmost hanger, rather than removing the two hangers as shown in the video.
2012 Sienna LE FWD. Watch the 2011 installation video before you start. This 13105 hitch tucks in even prettier than I expected, and now my brother is jealous. Note I made the cutout in the underbody panel narrower, starting 1.75 inches from the hole (see photo), for a closer fit, and there is still room for torque wrench. I also cut a slit out to the front edge, so I could slip it on with the hitch in place, and for better access to my air hoses inside the left fender. I decided to add Airlift after reading reviews, since on trips I carry a maximum load. Installed single-handed, raised on jack stands.
# 15
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
This receiver hitch is heavy duty and very well made. The welds are all smooth and uniform, and the powder coating was great. The bolts and mounting hardware were shipped safely in a sealed plastic bag tucked inside the receiver tube. Install on my Nissan Truck was easy. I would recommend running the threads on the truck frame before attempting to bolt the receiver hitch in place as the factory bolt holes can get filled with dirt and grime.
Excellent fit and finish. Welds are great. Bolted right up - super easy with no problems - I bet it took only 20 minutes to install it to my 22 Frontier, using only a floor jack to support out and a 19mm socket. Shipping was super fast, 2 days. Both the product and etrailer are highly recommended.
# 16
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
I cannot grade the towing capability yet, but this review is on installation. Less than one hour from start till I was putting tools away on the same day of arrival. One man job with the assistance of a rolling floor jack. Put rear up on ramps, hit holes with wd40, used one bolt to test run all threads, did not unhook tailpipe, simply insert the plate in, over, and let it rest on on exhaust (majority of weight still supported by jack). Start with left side, place 1 bolt loosely and then continue to switch sides with two at a time. Used torque wrench at 68 lbs to finish securing. Done. Looks great too! Up next: electrical and trans cooler. Thank you etrailer for the product and videos. Bought the hitch bc of such great reviews.
This can be a one man job if you have ramps and a short step stool. The thing that made the install take longer than 30 minutes was that the bolts on the passenger side would not line up if the drivers side bolts were on. I had to remove all the bolts on the driver side and set the hitch on a step stool 12 inches high so that the driver side was about 3 inches away from the mounting location. This was the only way i could get all three passenger side bolts to line up. Torqued to 69 pound-feet and i was done. Three stars for those three bolts.
# 17
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
I have been looking for a hitch for awhile now and then I came across your web page. I have seen Draw-Tite hitches on quite a few vehicles. So I went on to do a little research and to read quite a few of the reviews on this hitch here. After reading the reviews and the price of the hitch at that time I decided that I had found the hitch for my 2011 Dodge Grand Caravan Crew. I placed the order and the next day received a message that my order had shipped. The box arrived very quickly after I placed my order which was a pleasant surprise. One side of the box was really tore up and the hitch had come free of the strapping inside the box. The only thing inside the box was the hitch with the tongue/receiver wrapped in plastic wrap and the two pieces of cardboard that had come free. I search the inside of the box for some instructions but did not find any at this point so I would know exactly which bolts to take out. The first thing I did was to jack up the back of my van so I had a little more room to work underneath where the hitch was to go. Then I took off the passenger side rear tire to give me better access to the bolts that had to come out for the hitch and for the exhaust system to be lowered. I then took out the five bolts for the hitch and had to take out the three bolts holding up the exhaust to give me room to install the hitch. Then came the hardest part of the whole process and that was getting the hitch up to a point where I could get a bolt started. I tried using the exhaust system to help me but was still having a problem. So I got a cinder block I had in the garage and put it under one end of the hitch which was a better platform and really helped me getting the other side started. From that point on it went really well getting the other side started and then all five bolts in and tightened down. I then stepped back to see what it looked like and at this time I saw something white deep in the hitch receiver/tongue. When I pulled it out I noticed it was the instruction I had looked for earlier. It would have been nice to have these when I first started. A suggestion would be to put a notice on the plastic wrap that is wrapped around the receiver/tongue of the hitch that states "Instruction Enclosed" or "Packing Slip Enclosed" or just tape them to the inside of the box, not hidden inside a wrapped receiver/tongue of the hitch. I then went back and torqued the five bolts to what it stated on the sheet I found. I then put the three bolts back in the exhaust system to get it back in place which basically completed the installation of my Draw-Tite Max-Frame Trailer Hitch.
Went on like a charm. This is my 3rd rodeo with Etrailer. Two receiver, hitches, and a weight distribution camlock. All of them were exactly as promised.
# 18
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
This was installed on a 2016 highlander le plus. As advertised it fits perfectly and looks great. As a DIY-er, I was able to successfully install this hitch alone and make the correct cuts in under an hour. The hitch weights about 50lbs and once you set it into position (with help from jack stands), the screws go right in. It really is as simple as the video available online. Highly suggest this hitch. If negative things happens I will post a follow-up review. I don't expect it. Worth the price!
I received the hitch on time and no damage to the box and no scratches on the hitch. The directions were easy to follow and had the hitch installed in about 1.5 hours, I didn't have to jack up my vehicle (2016 Toyota Highlander), the hitch was light enough that I was able to lay it on my lap and start a bold on each side then work my way back installing the remaining 4 bolts. I torqued the bolts to specifications as stated in the directions then installed the wiring harness, that only took 15 min start to finish. I towed a 5' x 8' [rental] trailer with furniture on a 8 hour trip with no issues. Buying the hitch was cheaper that renting a truck to move my daughter into an apartment for her Junior year of college. Thanks again for a great product at a great price.
# 19
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
Read instructions , gather the tools needed and in less than an hour you are ready to go, for sure less if you get someone to help you, I did it by myself. Great products, awesome service.
I highly recommend this project! It is good quality and a good price. I do suggest getting a swivel socket adapter for the hard to reach places. You don’t need to jack the vehicle up but it is easier to jack it up to my your life easier. Installing it was not hard but it did take me a bit to do it. The shipping was good it came pretty fast and had great packaging and on the order they tell you who even packaged it. All and all I really recommend it
# 20
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
Hitch (Part 13241) and electrics (Part 118266) arrived on time, 40 minutes later everything was installed and connected. Had to ream out the washers to fit the bolts and drill new holes in the Mounting Box (Part 18157) to fit the 7-Way connector ... overall good value.
Fairly quick shipping for a new model year vehicle. 15 minutes to install and looks great, and we'll made. Would highly recommend etrailer.
What our customers are saying:
"hitch arrived on time, and it took me about 10 min to put it on . thanks alex"