Best 2008 Chevrolet HHR Bike Racks

Rack arrived in good condition and easy to assemble.However,the frame cradles on the horizontal bars are so fat, I cannot get my ebike on them using a bike beam as I intended. My regular bike will go on the rack with slight difficulty so I can only use it for that one.

I have put my bike rack together having little trouble because the instructions are quite good. I am very pleased with the rack's construction. I will be mounting it on my HHR this weekend for a test run with my bike mounted for 10 - 15 minutes trip thru town and some highway miles. Being as I've never used a bike rack before I'll be making frequent stops to check the rack & bike straps. I will be using the rack soon and I'm excited about having my bike for the up coming vacation.

We have kept the bike rack on the car all this year. It worked well for us. It fit the odd shape of our Chevy HHR. We had no problems with the rack. It was a little difficult to get the hard rubber latches together, but it became easier as time went on. We carried an adult bike and a child's bike.

The product is easy to use and get set up. I am able to get everything up and going in a few minutes.

The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.

Click to Enlarge

Hitch pin broke before I got it. Looks like a poor design for the locking pin, they might want to consider a different design. I got a 3/8 shear pin from Home Depot to replace and it works great. Bike rack is great!

Click to Enlarge

At the age of 70, I needed a “friendlier” mounting and bike access rack. A platform rack seemed to be the solution. I had one caveat. My Subaru Forester had a 1and 1/4” receiver (with a non-standard 3/4” length mounting hole). My Volvo had a tuck away 2” receiver. After some research I gravitated toward Thule only to find out they had no solution for my above conundrum. In fact their customer service offered no interest in solving my problem which others also must have had. More research…enter Saris! An American made company with an innovative solution. I quickly received my SuperClamp EX-2 from ETrailer along with excellent customer service support. The ease of constructing the unit for use and the obvious structural integrity was immediately apparent. My wife couldn’t believe how easy it was to use and to stow away on my garage wall after use. Thank you Saris and ETrailer for a wonderful product and experience. I guess American made is still alive and well. I highly recommend this product and the associated companies.

Purchased this bike rack last year and am very pleased with the stability of the rack. The straps and clamps secure the bike well to the rack. Some things that I learned: When attaching the rack onto your hitch, it helps to put a piece of tape on the rack (hitchtite) once you have lined up the holes. This will make it easier to find the exact location of the holes the next time that you want to use the rack. Finding the exact location allows you to smoothly hand tighten the bolt to the end of the hitch. At that point, just use a socket wrench to finish the tightening. When putting the bike on the rack, I loosely secure the clamps to the tires at first. This allows me to rotate the tires to find the right location in the wheel well for the straps to go around the spokes. I next secure the bike with the straps and then fininsh securing the clamps to the tires.

Rack arrived in good condition and easy to assemble.However,the frame cradles on the horizontal bars are so fat, I cannot get my ebike on them using a bike beam as I intended. My regular bike will go on the rack with slight difficulty so I can only use it for that one.

I have put my bike rack together having little trouble because the instructions are quite good. I am very pleased with the rack's construction. I will be mounting it on my HHR this weekend for a test run with my bike mounted for 10 - 15 minutes trip thru town and some highway miles. Being as I've never used a bike rack before I'll be making frequent stops to check the rack & bike straps. I will be using the rack soon and I'm excited about having my bike for the up coming vacation.

etrailer has the best pre- and post-sales customer service I've ever seen! I started out not knowing anything about hitch-mounted racks. So I wrote to etrailer telling them about my car and type of hitch I was about to have installed. Samuel wrote back with lots of great information tailored specifically to my car. He even included a photo that looked just like my 2017 white VW GTI with a hitch and rack installed. Okay something of a coincidence. But the rest of the assistance I got from the crew at etrailer was just as prophetic. I went into this a novice and came out knowing lots more about hitches and racks and finding the rack best suited to my situation. I have a small car, a class 1 hitch and a heavy mountain bike. I got exactly what I needed. As to the Swagman rack itself, it works fine. If I had a different situation I would probably buy a platform rack as they are easier to load. There's no reason to buy a bike rack anywhere else.

Click to Enlarge

First off, thanks to Jason T. or "Troop". The exemplary customer service he provided is rare these days. Troop made several calls to the various manufacturers to ascertain which bike rack would afford me the most ground clearance as my new VW Golf sits low to the ground and my old bike rack frequently scraped the ground when I went up even a slight up hill grade. His efforts paid off as he found me the best bike rack for my car, the Swagman Trailhead 2 Bike Carrier. It sits up off the ground just high enough that it doesn't scrape on my driveway. It is also sturdy and holds my bikes securely. And, the delivery was amazingly fast. I had my rack in about 2 days! Note to Troop, see my Pittsburgh Pirates Logo on my bumper in the attached pictures? Pirate Fans persevere! The Bucco's will be coming after your Cardinals this year! Thanks again Troop!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Super easy to use and remove. Just pull the straps tight and secure your bike to the loops. Use a piece of styrofoam or cardboard between the bike or bike pedal and your truck lid to prevent any scratching of the paint on your car.

Got here much faster than expected, and setting it up on the back of my car was pretty straightforward and easy! Thanks for the excellent customer service!

This rack is perfect! eTrailer had it shipped and at my home in almost no time. I drove with it on the car today, and it was solid and secure. It's super easy to get on and off the hitch. I'm 5'1 and I was able to load the bike on with the ramp without a struggle. Thanks for the thorough video and comparison information. It made this purchase easy.

Click to Enlarge

I purchased the rack and receiver hitch a year ago. Installation of the rack was made simple with the installation video that was specific to my vehicle (2020 Honda Accord). Literally took less than an hour start to finish. Only tool that I needed to buy was a torque wrench, which was about 20 bucks. It did require a very small cut in the plastic bumper that was accomplished easily with a keyhole saw. There was no drilling or other significant issues. The rack itself is awesome! My wife and I have two Lectric XP3 bikes. They weigh about 65 pounds each with battery. When we travel I revome the batteries to save a bit of weight. I have made two cross country trips (over 6000 miles) with this rack and have never had an issue. Literally every gas stop or hotel stop someone asks me about the rack and bikes. It really is that nice. My wife usually scolds me because we lose a 1/2 hour of travel time each stop to visit with complete strangers:) The rack is easy to install and remove on the receiver hitch. The lockout feature works great and gives a great deal of peace of mind. The bikes are easy to load. I don't use it, but there is a ramp that could make loading the bikes easier if a person couldn't lift the bike onto the rack. There are two arms the lock onto the frame of the bikes similar to the receiver hitch. Once locked down the bikes will not move. I would recommend ordering the longer ratchet staps if you have fat tires. I think they cost around 20 bucks but the longer straps allow for a little more flexibility in arranging bikes on the rack. I would strongly recommend this product and this company.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I installed this rack onto a Curt trailer hitch which is mounted onto a 2017 Honda Fit. I have been using it intermittently for several months, probably about 5 times with one bike and twice with two bikes. I give some pros and cons below and then elaborate. Pros: easy to assemble, easy to mount and dismount bikes, easy to lock and unlock, how to put the rack into different positions is intuitive Cons: inconvenient to put the rack into different positions, inconvenient to mount the rack onto the hitch, rack protrudes about 15 inches from bumper when in flipped up position (seems very vulnerable to someone backing into it in a parking lot, very inelegant looking I say the repositioning is intuitive because there is really only one way you could possibly place the pins for each position. But removing and replacing two pins is much less convenient than turning a knob or a lever, like some racks do. Also many racks fold and flip in such a way as to look very unobtrusive when in non-use mode. This one looks like kind of a monstrosity. That does not really bother me but it might bother some owners. The part that does bother me is how far it protrudes from the car. I back into parking spaces whenever possible to avoid someone bumping into the rack and damaging it (which happened to a friend). My number one suggestion for Curt is related to mounting the rack onto the hitch. Make it easier to tell when the holes are lined up so that the bolt/pin will fit and thread. As it is now, if you insert the rack as far as it can go it is way too far in. Ideally, it would be exactly lined up. Failing that, maybe some kind of click or other feedback to know at least that you are in the neighborhood. It would also be great to have an attaching device that is easier to fasten and unfasten than is the bolt/pin. Tip for mounting the rack onto the hitch: I assumed that it would be awkward to hold, what is it 46 pounds?, while trying to line up the rack probe with the receiver. If you have a garage with exposed collar ties, my solution could work well for you. I looped a cargo strap over a collar tie. Then I hooked both hooks of a bungie onto that loop. The idea is that you hook one of the bike frame holders of the rack onto the bungie, suspending the rack a few inches off the garage floor. This takes most of the weight of the rack so that you can just pull up or down and forward until you line up with the receiver. Tip for mounting bikes. Don't put the little screw into the post that prevents you from completely removing the bike frame holders. Remove both holders. Position the first bike, slide the holder into place, position the second bike, slide the holder into place. I found this makes it much easier, because you avoid parts of the bike hitting the holder as you are trying to get the wheels into place. The trick is that if you are mounting only one bike, don't forget to put the second holder back on - or maybe just stick it inside the car right away.

Click to Enlarge

Click to Enlarge

I had a 1 1/4" hitch installed on my 2016 toyota camry (the only size offered on the camry). I was very pleased with the ride. I expected to hear alot of noise like experienced when towing a trailer, but I heard almost nothing accept when going over speed bumps. I had to extend the tire supports to their widest position because having mountain bikes with a step through angled bar, they were more secure the closer i could get the upper and lower support arms to the seat post. The bikes were mounted in opposite directions and only stuck out maybe 6 inches or so. One locking barrel on the lower support arm was malfunctioning and gave me trouble but i called etrailer and they sent a replacement as soon as they were in stock. It comes with a anti rattle hitch pin but I highly recommend purchasing an anti rattle hitch pin with a lock on the end instead of just a clip for more security when unattended. After a few times mounting the bikes and figuring out the best way they should be positioned (pedals positions, direction of bike, and that my wife's smaller bike fit better going on first with my larger bike on the outside) I can mount the rack and bikes and be ready to go in just 5 minutes. (70 pounds on a torque wrench recommended for the hitch pin) I am overall pleased with my purchase i would recommend this product.