# 1
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
Worked great, towed my boat last weekend
The hitch works great. The service was excellent!!! I'm going back and having a hitch put on my other car soon. Thank you.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 3
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
The drop ball mount is the perfect size for my Jeep. The versatile hitch balls are convenient. Thank you for putting together a great kit, providing excellent communication, and delivering it quickly.
# 4
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
The ball mount was a complete failure even after a lengthy discussion on the phone. I wanted a ball mount that would accept the rocker ball and anti-sway bar. The bar sent to me can't be used this way. An email and phone message to the sales person I ordered with, got no response.
# 5
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Worked great, towed my boat last weekend
Excellent customer service & support! Bought for my 2013 Honda Fit and plan to trailer my Yamaha Tenere motorcycle around North America! Very happy with hitch.
# 6
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!
3.5 stars. Product looks like it should perform as advertised, but it arrived with several chips in the paint. This is most likely due to improper surface preparation and cleaning before the powder coat was applied. As you can see in the photos, there is already some surface rust on some of the areas, including the hole for the hitch pin. Ultimately the paint will get scratched up from use, but it would be nice to see some extra attention to detail from the factory.
# 7
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
What our customers are saying:
"WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!"