Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - GM

Tekonsha Accessories and Parts - 3026-P

Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.

Features:

• Wiring adapter eases installation of your electric brake controller
• Custom connector end plugs into the built-in port beneath the dash of your vehicle
• Other end plugs into the back of your electric brake controller
  • Compatible time-delayed brake controllers: Draw-Tite Activator I (5100), Draw-Tite Activator II (5500), Draw-Tite Activator III (5520) and Tekonsha PowerTrac (39523)
  • Compatible proportional brake controllers: Tekonsha Prodigy (90185), Tekonsha P2 (90885), Tekonsha P3 (90195), Tekonsha Primus IQ (TK90160) and Tekonsha Voyager (39510)
• Limited 1-year warranty

Installation of Tekonsha Brake Controller Adapter

This adapter plugs into the 6-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.

To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.

This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.

3026-P Tekonsha Brake Control Wiring Adapter with 2 Plugs

Customers compare 3026-P to these similar products

Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - GM$14.99

Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - GM$14.99

Universal Installation Kit forTrailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires$64.80

Hopkins Plug-in Simple Brake Wiring Adapter - GM$12.95

Customers who look at this part also view

Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional$124.95

Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional$144.15

Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional$94.95

Tekonsha Prodigy Trailer Brake Controller - 1 to 4 Axles - Proportional$124.95

Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional$78.95

Customers Who Purchased This Accessories and Parts Also Bought...

Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional $124.95

Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot $1.21

Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional $144.15

Mounting Pocket for Tekonsha Prodigy Proportional Brake Controller $10.99

Tekonsha Replacement Cradle and Mount Bracket for P3 Brake Controller $16.98

Ask the Experts about this Tekonsha Accessories and Parts
Do you have a question about this Accessories and Parts?

• Brake Controller and Wiring harness Installation Instructions for a 2011 GMC Acadia with Tow Package
  
• Yes, it really is just that simple. You will just plug the larger gray connector from the Tekonsha Wire Replacement, item # 3026-P, into the connector located under the dash and then plug the small black connector into the back of your brake controller. The vehicle harness will be located underneath the dash and left of the steering column, taped to another harness near the emergency brake pedal on your 2011 GMC Acadia, see photo at right. Since your vehicle is equipped with the OEM towin
  view full answer...


• Trailer Brake Controller Wiring Adapter for a 2010 Chevy Traverse and Tekonsha Prodigy Controller
  
• The Tekonsha Wire Replacement, # 3026-P, is the correct wiring adapter for a 2010 Chevy Traverse with a factory installed 7-Way trailer connector. I have included a link to the installation instructions for the adapter for you. This harness is also compatible with the Tekonsha Prodigy Brake Controller, # 90185.
  view full answer...


• Which Wiring Harness Do I Need To Install Brake Controller on 2009 GMC Acadia
  
• If your 2009 GMC Acadia has a factory 7-way connector at the rear of the vehicle, you will need to use the Tekonsha Wire Replacement, part # 3026-P. This connector works with Tekonsha brake controllers, like the Prodigy P2 Brake Controller, part # 90885. If your 2009 Acadia does not have a factory 7-way, you would not use the # 3026-P Teknonsha Wire. Instead, you would need to use the Brake Controller 7 and 4 Way Installation Kit, part # ETBC7. To install the # 3026-P connector, one end wo
  view full answer...


• No Green Light On the Power Trac Brake Controller When Trailer is Connected to a 2011 Chevy Traverse
  
• The Electric Brake Controller Wiring Adapter, # 3026-P, is designed for use with the 2011 Chevy Traverse, if it has a factory installed 7-Way connector. Since you have a aftermarket 4-Way connector, like part # 118450, installed inline with the taillights and a 7-Way adapter, like part # 37185, that the 4-Way harness plugs into, you most likely will have to run at least one wire from the blue brake controller output wire to the blue electric brake feed wire on your 7-Way adapter at the receiver
  view full answer...


• Where is the Tow Package Wiring on a 2011 GMC Yukon to Install a Prodigy Trailer Brake Controller
  
• On a 2011 GMC Yukon, there will only be bare tow package wires tucked up under the dash instead of a plug. Look below the steering column and to the left of the brake pedal for the wire bundle. The wires you need will be held together with a white tag that also tells you what each wire does. The tow package wiring should be as follows unless otherwise noted on that white tag: Red/black tow package wire connects to black brake controller wire. White connects to white. Light blue/white tow
  view full answer...


• Where is the Brake Controller Port Located on a 2007 to 2012 GMC Acadia
  
• On a GMC Acadia, there is a trim panel below the dash and above the brake pedal. You will start be removing this panel carefully. There is a light attached to it so pull it down slowly so you do not break the light. With the panel out of the way, look for the connector to the left of the steering column taped to another harness near the emergency brake pedal. The harness has a plug on it that mates with the connector on harness # 3026-P. I have included some pictures showing the areas you
  view full answer...


• Parts Needed to Install a Brake Controller on a 2011 GMC Acadia without a Tow Package
  
• You can hardwire the brake controller to your 2011 GMC Acadia. If you do not have one already you will need a 4-way at the rear of your vehicle. For a 4-way I would recommend you get a Tow Ready Custom Fit Vehicle Wiring Harness # 118451. I attached installation instructions and an installation video for this product for you to check out also. Now to convert your 4-way to a 7-way you will need a Brake Controller Installation Kit # ETBC7. This comes with everything to hardwire your brake co
  view full answer...


• Wiring in a Trailer Brake Controller on a 2013 Chevy Suburban 1500
  
• Chevy used to have a plug in port for a brake controller harness for trucks and full size SUVs but they stopped doing that several years ago (2006 was the last year). Now there should be a bundle of wires tucked up underneath the dash held together with a tag. The tag also lists the functions of the wires on it. You will just need to splice the brake controller wires to the tow package wires by functions. On the controller, the white wire is ground, black is 12 volt power, blue is output to t
  view full answer...


• Can a Tekonsha P2 Trailer Brake Controller be Moved From a Ford to a 2012 Dodge Ram 1500
  
• For your 2012 Dodge Ram you will need wiring harness # 3021-P to plug into your P2, # 90885, and your truck. I have linked the instructions for you to view. If you need another mounting bracket use # 7686.
  view full answer...