Replacement Multi-Tow 7-Way and 4-Way Trailer Connectors for Ford, GM Trucks with Factory 7 Way

Hopkins Custom Fit Vehicle Wiring - 30955

7-Way US car connector (car end) fits 97-Current Ford, 99-Current GM and 04-current Nissan full size trucks and SUVs equipped with factory socket.

• Durable plastic shell
• Provides Both a 7-Way and a 4-Way Covered Trailer Connector
• Mounting Bracket Included
• Visible wire measures 6-3/4" from vehicle end to trailer end
• Measures 10-1/2" from vehicle end to back of trailer connector

Close-up Picture of the Connector

Picture of the OEM connector on a Chevy truck. The connector is located above the spare tire and simply plugs in to the 7-Way and 4-Way Replacement Connector.

Video of Replacement Multi-Tow 7-Way and 4-Way Trailer Connectors for Ford, GM Trucks with Factory 7 Way

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Trailer Wiring Harness Installation - 2006 Chevrolet Silverado

Trailer Wiring Harness Installation - 2007 Chevrolet Silverado

Trailer Wiring Harness Installation - 2006 GMC Sierra

Trailer Wiring Harness Installation - 2005 Nissan Armada

Customers compare 30955 to these similar products

Pollak 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End$29.95

T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector$29.95

Customers Who Purchased This Custom Fit Vehicle Wiring Also Bought...

Bonded 4 Wire - per foot $0.57

Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot $1.21

Pin and Clip For Class III, IV and V Trailer Hitch Receiver $5.16

Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - GM $14.99

Ball Mount 3/4" Rise or 2" Drop, 7,500 lbs $17.20

Ask the Experts about this Hopkins Custom Fit Vehicle Wiring
Do you have a question about this Custom Fit Vehicle Wiring?

• 2006 Hummer H3 Does Not Require a Converter or Modulite
  
• Your vehicle does not require a converter or modulite. If your H3 has the tow package, you will use the Replacement Multi-Tow 7-Way and 4-Way Trailer Connectors for Ford, GM Trucks with Factory 7 Way, part # 30955. If you do not have the tow package, you will use the 4-Pole 60 inch Long Vehicle End, part # 18002 to hardwire a 4-pole into your vehicle.
  view full answer...


• Wiring a Brake Controller on a 2007 Chevy 1500
  
• The brake controller itself will splice into the bundle of taped or banded wires under the dash, usually located above where your left knee would be as you are sitting at the wheel. The wires do now connect color for color. The red wiring harness wire would connect to the black wire on the brake controller, the dark blue harness wire connects to the blue wire on the controller, the light blue harness wire attaches to the red wire on the controller, and the white wire on the harness connects to t
  view full answer...


• Wiring Harness for a 2003 Ford F-250
  
• You would need part # 30955. Please let me know if there is anything else with which I can assist you.
  view full answer...


• Turn Signals on 2007 Nissan Titan Not Working with Replacement 7-Way Trailer Connector # 30955
  
• The item you selected, 30955, does not have the relays included to activate the tow package on your vehicle - thus no turn signals. You need # N40975, the Factory Style 7-Way and 4-Way Flat. This item has the relays you need for the activation of the factory tow package. I also recommend using a circuit tester like # 40376 to test your 7-way on the vehicle end for proper function. The yellow wire is the left turn signal and the green is the right signal. These are also your brake lights. The whi
  view full answer...


• 7 and 4-Way Connector for a 2008 Ford Expedition
  
• Since your truck has a factory 4-Way connector at the rear of the vehicle you will need the Adapter 4 Pole to 7 Pole and 4 Pole, item # 37185, which is designed for the 1997 - 2008 Ford Expedition with factory 4-Flat. The connections for a the brake feed, power and auxillary functions will be on the forward side of a connector that is attached to the driver side frame rail above the spare tire. You will need to splice the needed connections into the wiring using a circuit tester, item # 3808, to
  view full answer...


• What is the Difference Between Valley 7-Way V30607 and Hopkins 7-Way 30955
  
• The Hopkins part # 30955 and the Tow Ready # 20119 work the exact same way and offer the same features. The mounting brackets are a bit different, and the wire on the 20119 is covered by wire loom for a neater appearance, but the two connectors operate the same way and have the same vehicle side connector. Now, your truck may have a knock out on the rear bumper with a pre-cut 7-Way mounting location that you might like better. No need to hang an existing bracket, the down side is you would ne
  view full answer...


• Items Needed to Replace and Relocate a Broken OEM 7-Pin Plug on a 2007 Toyota Tundra
  
• There are several options for installing a 7-way or 7-Way and 4-Way at the rear of your 2007 Toyota Tundra. I will list the options below, so you can determine which will be the best option for relocating your connector to the bumper of your vehicle. The Pollak 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End, item # HM40975, is the connector we normally recommend as a direct replacement for your truck. We have a video review of this connector for you to check out, see
  view full answer...


• Adding a New 7-Way Trailer Connector to a 1992 Ford F-250 that Previously Had a 7-Way
  
• What you will need to do is test the plugs you have found with a circuit tester like # 3808 if needed. You will be testing for the various lighting functions, brake controller output (if still installed) and a good ground. If all the signals are there and working properly, you can hardwire in a 7-Way trailer connector. I recommend a multi-tow, like # HM48470, so you will have a 4-Way, 5-Way, and a 7-Way. What you will do is remove the plug on the end that works, clip it off, and attach the wi
  view full answer...


• 7-Way Bumper Mount Replacement Trailer Wiring Connecter for a 2004 Ford F-250 Super Duty
  
• If your 2004 Ford F-250 Super Duty has a factory 7-Way trailer connector and you need to replace it then you can use the replacement Multi-Tow 7-Way and 4-Way Trailer Connector, # 30955. If your truck only has a 4-Way connector and you need to add a 7-Way connector, you can use the 4 Pole to 7 Pole and 4 Pole adapter, # 37185, and connect the additional wires to the wires going into the OEM connector along the drivers side frame rail under the truck. I attached a video and an article for you
  view full answer...


• Availability of a Replacement 7-Way and 4-Way Trailer Connector for a 2008 Ford F-250 Super Duty
  
• There are a couple of options for 7-Way and 4-Way connectors that you can use for a 2008 Ford F-250 Super Duty. First, you could use # 30955 that you have referenced. It fits 1997 to current Ford full size trucks. You can also use Replacement Multi-Tow 7-Way and 4 Pole Trailer Connector, # 20119. Both of these connectors come with a mounting bracket so they will not fit in the exact same place as the original 7-Way, but they will plug in to the factory wiring harness.
  view full answer...


• Replacement 7-Way Trailer Connector for a 2003 Ford F-150 with Factory Tow Package
  
• If the factory plug you are talking about on your 2003 Ford F-150 looks like the one in the picture I have included then # 30955 will fit. It is designed to fit the 1997 to current Ford trucks equipped with the factory socket in the picture. If your truck has square connectors then you would need to use a different harness, # 118242. I have included a link to a video showing a typical installation for you.
  view full answer...


• Changing from a 4-Way Flat to 7-Way Blade Trailer Connector on Trailer and 2003 Ford Ranger
  
• First I recommend going with a 7-Way blade style for your trailer and truck because that is the most common advanced function connector used. To add one on the trailer you can use # PK12706. If your trailer only has the basic light functions then you will only need to cut off the 4-Way and attach the wires according to the diagram I have included. Please note that when you attach the existing wires to the connector you cannot just go by wire color. You will need to go by function in then plac
  view full answer...