1998 Toyota Accessories:

Select Model for Your 1998 Toyota

1998 Toyota Accessories

Towing

1998 Toyota Trailer Hitch

1998 Toyota Trailer Wiring

1998 Toyota Brake Controller

1998 Toyota Base Plate for Tow Bar

Cargo Control

1998 Toyota Roof Rack

1998 Toyota Ladder Rack

1998 Toyota Truck Bed Extender

1998 Toyota Trunk Bike Rack

Performance Accessories

1998 Toyota Air Filter

1998 Toyota Suspension Enhancement

1998 Toyota Transmission Cooler

1998 Toyota Performance Chip

1998 Toyota Exterior Lights

1998 Toyota Tire Chains

1998 Toyota Throttle Body Spacer

1998 Toyota Vehicle Lightbars

Vehicle Trim

1998 Toyota Floor Mats

1998 Toyota Tonneau Cover

1998 Toyota Tube Steps

1998 Toyota Trim Kits

1998 Toyota Vehicle Covers

1998 Toyota Grille Guard

1998 Toyota Bug Shield

1998 Toyota Side Window Vents

1998 Toyota Truck Bed Mat

1998 Toyota Bumpers

1998 Toyota Mud Flaps

1998 Toyota Lamp Guards

1998 Toyota Truck Tailgate Lock

1998 Toyota Truck Bed Rail Caps

1998 Toyota Vehicle Tent

1998 Toyota Vehicle Seat Covers

1998 Toyota Replacement Mirrors

1998 Toyota Windshield Wiper Blades

1998 Toyota Questions and Answers

• How Does the Draw-Tite Custom Fit Vehicle Wiring Install on a 1998 Toyota RAV4
  
• I attached a set of installation instructions for the Draw-Tite Custom Fit Vehicle Wiring # 118388 that you referenced. But basically, you will open the rear hatch, push the rear seat forward, remove the rear threshold panel, storage covers and floor covering. Next, you will remove the rear interior trim panels. Several trim panel fasteners will need to be removed. To make removing the fasteners you may also be interested in purchasing a Fastener Remover # IB35260. Once you get into the re
  view full answer...


• Trailer Hitch and Wiring Recommendation for a 1998 Toyota Sienna
  
• Any of the Class III trailer hitches for the 1998 Toyota Sienna, see link, will have just the receiver visible beneath the rear fascia on the vehicle. The backs of the hitches are welded closed. The full size spare should not be an issue. Take a look at the video for Hidden Hitch # 87638 that I have linked for you. The spare on this vehicle is a regular size, not a mini spare, and it appears there is plenty of space available. For trailer wiring you can use # 43475. I have linked an installat
  view full answer...


• Lockable Tonneau Cover Recommendation for a 1998 Toyota Tacoma with a 6 foot bed
  
• Check out the Access Tonneau Cover # 834532000432. This cover uses a single latch with a slide lock that will prevent the cover from being opened without the tailgate first being opened. So if you got a locking tailgate handle like the Pop and Lock Custom Tailgate Lock # PAL5100 as well as the # 834532000432 you would be able to lock the tailgate and prevent access to the truck bed of your vehicle.
  view full answer...


• What is the Correct Mounting Hardware for a Thule Weekender Cargo Box for a 1998 Toyota 4Runner
  
• According to Thule you can use the QM3 mounting hardware, # TH04997, for the Weekender cargo box. The crossbars on your 1998 Toyota 4Runner will need to be up to 3-5/8 inches wide. I have included a picture that shows how this hardware will install.
  view full answer...


• Trailer Hitch, Ball mount, Balls, and Wiring for a 1998 Toyota Camry
  
• The Draw-Tite trailer hitch # 24563 is not a fit for the 1998 Toyota Camry but we do have several hitches that will fit. I have included a link to them for you. The most popular option is Draw-Tite trailer hitch # 36336. I have included links to the installation instructions and a link to a video showing a typical installation for you. If you plan on doing some towing the recommended ball mount is # 36061 and you can use pin and clip # PC2. For a 1-7/8 inch ball use # 19256 and for a 2 inch b
  view full answer...


• Will the Thule Vertex Swinging Trailer Hitch Mount Bike Rack Fit a 1998 Toyota 4Runner
  
• You will need to measure the distance from the center of the hitch pin hole out to the distance required to clear the rear of the vehicle. If that distance is less than 8-1/2 inches then the Vertex swinging rack # TH9031 will fit. The spare tire under the vehicle should not be a problem provided it is a factory sized spare mounted in the factory location. I have included instructions and video links on the bike rack for you. If you will be carrying womens, childrens, or alternative frame bik
  view full answer...


• Install Instructions for Curt Class III Receiver # 13157 on 1998 Toyota 4Runner
  
• I have confirmed that the Curt # 13157 is indeed a fit for your 1998 4Runner. To view or print the installation instructions, click on the provided instruction link.
  view full answer...


• Troubleshooting OEM 4-Pole Trailer Connector on 1998 Toyota Land Cruiser
  
• I could not find any information about the specific location of the fuses that protect the towing circuits on your 1998 Land Cruiser. Typically, these fuses can be found in a distribution box under the hood. By all means, you can check the ground for the connector on the vehicle and on the trailer, but it does not sound like a ground problem. I did come across a reference to a technical service bulletin issued by Toyota regarding the towing wire harness converter replacement which might i
  view full answer...


• Roof Rack and Side Step Recommendations for a 1998 Toyota 4Runner
  
• For side steps, we have several options for a 1998 Toyota 4Runner. I have included a link to the available options for you. For silver steps, we have # CARR103994 and # CARR124034 that you have referenced. I have included links to the installation instructions for each set for you. For a roof rack, there are 3 different roof options that were available on the1998 Toyota 4Runner. You could have factory tracks that run front to back, a plain roof with no rails, crossbars, or tracks, or a factor
  view full answer...


• Firestone Fuse Circuit Tap Kit Recommendation for Installing a CB in a 1998 Toyota Tacoma
  
• This Firestone Fuse Circuit Tap Kit # F2526 should work for installing a CB radio in your 1998 Toyota Tacoma. If there is a fuse already protecting the CB radio I would recommend putting in a fuse that is the same rating or higher for the # F2526. If you were to go lower you would most likely end up popping fuses on the # F2526 pretty frequently from amperages that are actually safe for your CB.
  view full answer...


• Which Trunk Mount Bike Racks Will Fit a 1998 Toyota Corolla
  
• The Rhode Gear Super Shuttle, # RG8015126, does not have a specific fit guide. However, its design is similar to the Yakima SuperJoe bike racks, like # Y02630, which does have a fit guide and is listed as a fit, so there is a good chance the Frontier will fit as well. I have also included a link to the trunk mount bike racks that are confirmed fits for your 1998 Toyota Corolla. If you will be carrying womens, childrens, or alternative frame bikes, I recommend using an adpater bar like the Yak
  view full answer...


• Parts Needed to Install an Electric Brake Controller on Two Vehicles for Towing a Camper Trailer
  
• Yes, you can set up both of your vehicles for towing trailers with electric brakes. The only requirement is that you have a 12 volt constant power source for the brake controller you choose, and that you have a brake light signal that has 12 volt power only when the brake pedal is pressed. The Prodigy P2, # 90885 brake controller, would make a great choice for moving from one vehicle to the other, with the addition of a second mounting pocket, # 7686 and a second plug-in harness, # 20127. Yo
  view full answer...


• Left Turn Signal Makes Right Trailer Signal Blink With Hopkins Wiring Harness,1998 Toyota Sienna
  
• I suppose it is possible that something, somewhere was not installed correctly when you installed the Plug-N-Tow Wiring harness, # 43475, into your 1998 Toyota Sienna. There is an easy way to determine if you have the sides switched. The wires with yellow, red, and brown plug into the driver side tail light wiring. The Connector with the green wire plugs into the passenger side tail light wiring. make sure that the white ground wire is attached to a bare metal surface. Looking at the picture
  view full answer...


• Replacing a CURT Trailer Brake Controller with a Tekonsha P3 on a 1998 Toyota 4Runner
  
• I believe that you have an older version of the CURT Discovery brake controller. The CURT controller and the Tekonsha P3, # 90195, use different connecting plugs. However, you could hardwire the P3 to the CURT wiring harness by cutting off the plug on the CURT harness. It looks like the CURT harness uses the same color/functions configuration as the P3. White is ground, black is 12 volt power, blue is output to the trailer, and red is input from the brake light circuit. Use a circuit tester
  view full answer...


• Does the Edge Insight Tune the Engine and Add Power to a 1998 Toyota RAV4
  
• The Edge Insight, # EP83730, will not give your 1998 Toyota RAV4 more power. What it does is provide myriad monitoring features and displays them for you. The data parameters you can monitor include: Battery Voltage Intake Air Temperature (IAT) Engine Oil Pressure (EOP) Engine Coolant Temperature (ECT) Engine Oil Temperature (EOT) Transmission Fluid Temperature (TFT) Miles Per Hour (MPH) Miles Per Gallon (MPG) Revolutions Per Minute (RPM) 1/4-mile and 0 - 60 times
  view full answer...


• Wiring The Hayes Energize III Brake Controller # 81741B To A 1998 Toyota 4Runner
  
• You will want to make sure the four remaining wires from your 4-flat to 7-blade adapter are connected as follows on your 1998 Toyota 4Runner: White: Ground wire, connected to a suitable grounding point on the vehicle frame. Blue: Electric brake wire, connected to the electric brake wire coming from the back side of your Hayes brake controller. Black: 12v power wire, connected to the vehicle positive battery terminal with a 40amp circuit breaker. Purple or Yellow: Used to power reverse l
  view full answer...


• Will the Kuat Alpha Bike Rack Clear the Spare Tire on a 1998 Toyota RAV4
  
• The Kuat Alpha, # A102-BLACK-114, and # A103-WHITE-114, measure 10-1/2 inches from the center of the hitch pin hole to the back of the up right bars. So they will fit, but it will be a tight fit on your 1998 Toyota RAV4. I have included a video review of the Alpha below. The Kuat racks are very light weight, 14-1/5 pounds in this case, and still boast a 100 pound capacity. I think you will be very happy with the performance and style of the Kuat Alpha.
  view full answer...


• What Hardware Is Included in the Westin Diamondstep Bumper and Install Kit for a 1998 Toyota Tacoma
  
• Included in this kit are 2 brakcets (driver and passenger), 8 lock washers, 8 flat washers, 2 12MM bolts, 6 1/2-13 bolts, and 6 1/2-13 nuts. The hardware included replaces the factory bumper brackets. This kit includes the bumper and all necessary hardware to install the bumper onto your truck.
  view full answer...