1994 Jeep Accessories:

Select Model for Your 1994 Jeep

1994 Jeep Accessories

Towing

1994 Jeep Trailer Hitch

1994 Jeep Trailer Wiring

1994 Jeep Brake Controller

1994 Jeep Front Mount Hitch

1994 Jeep Towing Mirrors

1994 Jeep Base Plate for Tow Bar

1994 Jeep Vehicle Tow Bar Brake System

1994 Jeep Vehicle Tow Bar Wiring

Cargo Control

1994 Jeep Roof Rack

1994 Jeep Trunk Bike Rack

1994 Jeep Vehicle Cargo Control

Performance Accessories

1994 Jeep Cold Air Intake

1994 Jeep Air Filter

1994 Jeep Exhaust

1994 Jeep Suspension Enhancement

1994 Jeep Transmission Cooler

1994 Jeep Exterior Lights

1994 Jeep Tire Chains

1994 Jeep Throttle Body Spacer

1994 Jeep Fluid Filters

1994 Jeep Vehicle Lightbars

Vehicle Trim

1994 Jeep Floor Mats

1994 Jeep Tube Steps

1994 Jeep Trim Kits

1994 Jeep Vehicle Covers

1994 Jeep Grille Guard

1994 Jeep Bug Shield

1994 Jeep Side Window Vents

1994 Jeep Bumpers

1994 Jeep Interior Trim

1994 Jeep Lamp Guards

1994 Jeep Vehicle Tent

1994 Jeep Vehicle Seat Covers

1994 Jeep Replacement Mirrors

1994 Jeep Windshield Wiper Blades

Jeep Accessories

1994 Jeep Replacement Top

1994 Jeep Jeep Doors

1994 Jeep Jeep Seats

1994 Jeep Jeep Windows

1994 Jeep Jeep Fender Flares

1994 Jeep Jeep Spare Tire Carriers

1994 Jeep Roll Bar Cover

1994 Jeep Jeep Hardware

1994 Jeep Questions and Answers

• Incorrect Blinker Function With Optronics LED Trailer Light, Part # STL53RCB, on 1994 Jeep Cherokee
  
• I note that you have also purchased an appropriate T-connector harness, part # C55330, to adapt these LED trailer lights to your Jeep Cherokee (which has a 3-wire lighting system) along with the appropriate load resistors. Based on your description of the problem, I suspect a bad ground connection. Check that the white ground wire with ring terminal from your pigtail lead is tightly secured to a clean (and preferably bare) metal surface. You might try sanding off any paint if the ground
  view full answer...


• What Needs to be Removed to Install the Roadmaster Base Plate Kit for a 1994 Jeep Grand Cherokee
  
• I am going to send you a copy of the installation instructions for the Roadmaster Base Plate Kit # 1411-1 also, but it looks like you will need to remove the tow hooks (if equipped), the two bolts securing the radiator cross members, the plastic splash guard retainer located behind the rear cross member bolt and the bolts for the tubular cowl support from the cross member.
  view full answer...


• Parts Needed to Flat Tow a 1994 Jeep YJ Wrangler Behind a Motor Home
  
• The first thing you are going to want to check is the vehicle owners manual to determine if the Jeep can be flat towed and if there are any special requirements. Both base plate kits for the 1994 Jeep YJ, # 1409-1 and # 1409-3 are standard kits and will fit your Jeep. The only difference is the design of each kit. Kit # 1409-3 has a crossmember and 1409-1 does not. And since they cost the same you cannot really go wrong with either one. For a tow bar, I have included a link to all of the tow
  view full answer...


• Trailer Wheel Pilot Hole Diameter is Too Small for New Hub and Drum Assemblies
  
• If the pilot hole on the wheel was larger than 4-3/4 inches, and the wheel is center on the hub using the lug nut rather than wheel bolts, it would not matter. But since the wheel pilot hole is smaller, you will not be able to use the hubs you purchased without also replacing the wheels. I went out to the warehouse and measured a Trailer Hub and Drum Assembly, # 42866UC3, to determine the diameter of the center portion that goes through the pilot hole of the wheel. Using some digital dial cal
  view full answer...


• What Parts are Needed to Flat Tow a 1994 Jeep Wrangler Behind a Nissan Xterra
  
• Flat towing a vehicle requires 5 components: base plates, tow bar, safety cables, lighting, and a supplemental braking system. For your 1994 Jeep Wrangler you would need base plates, # 1409-1 that you have referenced. These are standard base plates that provide a secure and safe attachment point for a compatible tow bar. For a tow bar, the most economical is the Roadmaster Tracker Tow Bar, # RM-020, with a 5,000 pound capacity. I have included a link to the installation details for you to
  view full answer...


• Will Brake Lock Up on 4000 lb Towed Vehicle Have Any Effect on Hitch with 5000 lb Weight Rating
  
• The vehicle being towed would represent rolling weight. If the braking system on the towed vehicle would activate the towed vehicle would skid, and not come to an immediate dead stop. The force exerted might be momentarily more than the 5000 lbs, but no more than a trailer with electric brakes that have been activated. I would not be concerned, a hitch with a 5000 pound capacity. Using a quality tow bar that has been properly installed will work just fine for you.
  view full answer...


• Will the Step Bumper Trailer Hitch # E-3S Fit a 1994 Jeep Cherokee Sport
  
• Part # E-3S has a 8-3/4 inch, center to center, span between mounting holes. Check your bumper to see if it has two holes that are 8-3/4 inches apart. These are universal fit items so they do not fit specific vehicles. If you find that the # E-3S, bumper hitch will not work on your Cherokee we have several frame nount hitches that will work (see link). I would recommend the Curt Class III Trailer Hitch, item # 13084, for your vehicle. The Class III trailer hitch provides more options for towi
  view full answer...


• Wiring a 1994 Jeep YJ for Towing Behind a Motorhome
  
• The T-One harness you were looking at is to tow a trailer behind the Jeep. It will not work in reverse to tow the Jeep behind a motorhome. You will need RoadMaster part # RM-154. There are wiring diagrams on the page to show you how to wire it depending on the taillight configuration of your motorhome.
  view full answer...